奥林巴斯5670前置放大器_供应_中贸商网-贸易商务资源网

奥林巴斯5670前置放大器

发布时间:2017-06-21 07:33:48 产品编号:GY-5-148270333 分享

价格:0.00/只
品牌:Olympus/010-57464568
起订:1只
供应:100只
发货:3天内
信息标签:奥林巴斯5670前置放大器,供应,仪器仪表,试验机

联系时一定要说在【贸易商务资源网】看到的将给您优惠！如果您也想和该公司一样在网站发信息有好排名，点击立即免费注册，发布产品推广。

奥林巴斯Olympus 5670前置放大器/脉冲发生器，奥林巴斯5670脉冲放大器，5670脉冲发生器接收器

5670前置放大器/北京泰如专业供应平台，5670前置放大器/欢迎来电索取价格及产品资料010-57464568

奥林巴斯Olympus 5670前置放大器/北京泰如电子科技价格优惠，奥林巴斯各种规格扫查架专业供应

本着为“客户提供**的产品和**惠的价格以及**的售后服务”以宗旨，北京泰如电子科技有限公司在保证产品质量、性能的同时，还会定期回访，进行仪器与配件保养、维护及技术交流。让客户能得到**的服务、满意的价格、放心的使用。

5660B超声前置放大器可与超声探伤仪、测厚仪、声学发射仪器一起使用，可对超声信号进行超低噪音的放大。这款仪器具有以下性能：20 kHz～2 MHz带宽，可选的40 dB和60 dB电压增益。
5660C超声前置放大器可与超声探伤仪、测厚仪、声学发射仪器一起使用，可对超声信号进行超低噪声的放大。这款仪器具有以下性能：500 Hz～2 MHz带宽，可选的40 dB和60 dB电压增益。
5662超声前置放大器可与超声探伤仪、测厚仪、声学发射仪器一起使用，可对超声信号进行超低噪声的放大。这款仪器具有以下性能：50 kHz～2 MHz带宽，可选的34 dB和54 dB电压增益。
5670超声前置放大器可与超声探伤仪、测厚仪、声学发射仪器一起使用，可对超声信号进行超低噪声的放大。这款仪器具有以下性能：50 kHz～10 MHz带宽，40 dB电压增益。
5676超声前置放大器可与超声探伤仪、测厚仪、声学发射仪器一起使用，可对超声信号进行超低噪声的放大。这款仪器具有以下性能：50 kHz～20 MHz带宽，40 dB电压增益。
5678超声前置放大器可与超声探伤仪、测厚仪、声学发射仪器一起使用，可对超声信号进行超低噪声的放大。这款仪器具有以下性能：200 kHz～40 MHz带宽，40 dB电压增益。

Olympus wideband series of Panametrics AC coupled, broadband preamplifiers provides very low noise amplification of ultrasonic signals ranging from 500 Hz to greater than 40 MHz. Specifically designed for use with ultrasonic flaw detection, thickness gaging, and acoustic emission instrumentation, our preamplifiers are a cost-effective solution in general applications requiring high gain/low-noise amplification of low amplitude ultrasonic signals.

Our preamplifiers are ruggedly housed, completely self-contained, simple to operate, battery or AC powered units. They offer performance features such as very low noise (5 µV peak-to-peak noise referred to the input in Model 5660B), input protection for high voltage transients such as transducer excitation pulses, and the ability to drive long coaxial cables (greater than 500 feet or 152 meters with Models 5660B and 5660C). Both fixed gain and switchable gain versions are available, and custom units with special gain or bandwidth are available on special order.

Applications

Certain ultrasonic applications require the addition of a separate preamplifier unit to standard test systems in order to provide the additional gain or broadband signal-to-noise enhancement necessary for optimum signal acquisition. This is often the case in industrial applications involving flaw detection or thickness gaging of thick sections of materials exhibiting high ultrasonic attenuation such as nodular cast iron, brass, bronze, austenitic steel, rubber, Teflon®, or reinforced composites. A preamplifier is also an important component of acoustic emission test systems that require amplification of low signal amplitude events and the ability to drive long cables from remotely located sensors.
Panametrics preamplifiers have also been used in many widely diversified research applications including seismic studies, determination of the size and number versus scattered frequency relationship for acoustic scatterers in water (gas bubbles, zooplankton), crack detection in graphite vacuum arc-melt electrodes, and biological tissue analysis.

MODEL 5682

The Model 5682 Ultrasonic Preamplifier provides low noise amplification of ultrasonic signals ranging from 500 KHz to 25 MHz. The preamplifier, housed in a rugged enclosure, is very small and lightweight making it ideally suited for remote applications. The preamplifier can be powered with either a single 9 V battery for up to 50 hours of continuous operation or a local 9 V to 13 V DC supply (customer supplied). When battery operated, a multicolored LED provides feedback on battery status. This preamplifier is ideal for AUT and TOFD scanning.

Inclusions: The unit is supplied with one 9 V alkaline battery. All cables are sold separately and are offered in a variety of lengths and connector styles to accommodate transducer, instrumentation, and applications requirements.

	Potential increase in sensitivity using a tuned square wave pulser versus a spike pulser as a function of transducer center frequency.
	Response using a Model 5073PR 75 MHz bandwidth pulser-receiver with a V215-BA-RM 50 MHz permanent delay contact transducer coupled to a 0.075 mm (0.003") metal shim
	Spike excitation features sharp rise times adjusted by energy and damping values.
	Square wave has controlled rise and fall times with directly adjustable voltage and pulse width.
	A-scan comparison between 5073PR and 5072PR with 50 ohm damping and energy Position 1 to 5077PR set at 100 volts and tuned for frequency optimization. Gain set to noted dB level to normalize signal height from a 20 MHz delay line transducer.

Specifications*

MODEL	5660B	5660C	5662	5670	5676	5678
Voltage Gain (Inverting)	40 and 60 dB Switchable (RL > 1K ohm)	40 and 60 dB Switchable (RL > 1K ohm)	34 and 54 dB Switchable (RL = 50 ohm)	40 dB Fixed (RL = 50 ohm)	40 dB Fixed (RL = 50 ohm)	40 dB Fixed (RL = 50 ohm)
Bandwidth (-3dB)	20 kHz - 2 MH	500 Hz - 2 MHz	50 kHz - 5 MHz	50 kHz - 10 MHz	50 kHz - 20 MHz	200 kHz - 40 MHz
Equivalent Input Noise	5 µV p-p	5 µV p-p	10 µV p-p	15 µV p-p	20 µV p-p	30 µV p-p
Input Resistance	1M ohm	1M ohm	100K ohm	100K ohm	100K ohm	100K ohm
Input Capacitance (pf)	approx. 320	approx. 320	approx. 80	approx. 80	approx. 80	approx. 80
Input
Protection	300 V peak (Pulse Width <2 µs, 1% Maximum Duty Cycle)
Output	5 V p-p (RL > 1 K ohm)
Voltage	2 V p-p (RL = 50 ohm)			2 V p-p (RL = 50 ohm)
Output
Impedance	50 ohms in series with 4.7 fd
Max. Output	>500' (152 m)		50' (15 m)
Power	16 V ± 2 V supplied by 4 Alkaline 9 V, 655 mAh batteries
Requirements	Line operated units available. Add /110 VAC, /115 VAC, or /230 VAC to the Model Number (e.g. 5675/115 VAC).
Current Consumption	28 mA	28 mA	28 mA	32 mA	32 mA	36 mA
Battery Life	>40 hrs	>40 hrs	>40 hrs	>35 hrs	>35 hrs	>35 hrs
Dimensions	3" W x 2" H x 5" D (76 mm W x 51 mm H x 127 mm D)
Weight	1.4 lbs. (0.64 kg)
Operating Temperature	32° F to 122° F (0° C to 50° C)

*All specifications are subject to change without notice.

NEW - Model 5682 Ultrasonic Preamplifier

Voltage Gain: 30 dB @ 10 MHz
HighPassRollover: 0.5 MHz +/- 0.1 MHz
LowPassRollover: 31 MHz +/-1 MHz
Equivalent Input Noise: 11.5 µV RMS
Input Impedance: Nominally 700 ohms
Output Impedance: Nominally 50 ohms
Output Voltage: 2.5 V pk-pk
Protection: 500 V peak
Current Consumption: Nominally 14 mA
Power: 9 V alkaline battery or 9-13 V DC input (toggle switch)
Power Monitor: Three color LED for continuous power level indications
• Green: 7.0 - 9.0 V
• Yellow: 6.5 - 7 V
• Red: 5.0 - 6.5 V
• No light: <5.0 V (Low charge, replace battery)
BatteryLife:
>50 hours continuous operation
Connectors: Lemo® 00 Type
Dimensions: 2.25" x 4.3" x 1.1",
57.15 mm x 109.22 mm x 27.94 mm
Weight:
6.4 oz, 181 gr with battery;
4.8 oz, 136 gr without battery
Operating Temperature:
32° F to 122° F;
0° C to 50° C
Environmental: IP65

北京泰如电子科技以技术为先导，为客户提供高效、**和安全的检测解决方案。我们设计、并维护超声波探伤仪，根据客户需求定制特殊规格探头，满足于各行业，代理工业工业内窥镜，X射线和涡流检测设备，为航空航天、电力、石油天然汽车和钢铁等行业应用制定专业检查方案。主要代理品牌：美国GE、德国KK、美国奥林巴斯（Olympus）、汕头汕超、美国泰克（Tektronix）、美国福禄克(FLUKE)、美国安捷伦(Agilent)、**固纬（GW）、香港优利德（UNI-T）、新美达（美柯达）、沪船（船牌）等。

主要经营：超声波探伤仪、无损检测仪器系列、示波器系列、安规测试仪系列、分析仪器系列、红外测温仪系列、行业专用仪器系列、电子测试仪器系列、环境监测仪器系列、力学仪器系列、电工测试仪器系列、通讯仪器仪表系列、通用监测仪器系列、工程监测仪器系列、计量检测仪器系列、气体检测仪器系列、其他测试仪器等。

奥林巴斯Olympus脉冲发生器/前置放大器一览表;

联系方式

公司:北京泰如电子科技有限公司
状态:离线发送信件
姓名:张文庆(先生)
电话:010-57464568
手机:13699112842
地区:北京-通州区
地址:北京市通州区土桥中街140号金隅自由筑1-1-1706

邮编:100000
QQ:3081402071
商铺:http://m.ceoie.com/bjtrdz/

去北京泰如电子科技有限公司怎么走？上图中的红点是北京泰如电子科技有限公司在通州区的具体位置标注，操作左上角地图工具可以放大缩小哦。

点击分享到微信、朋友圈、QQ...