价格:1.00/ 桶
品牌:多少钱FUCHS PLANTOGEAR 100S//福斯
起订:10 桶
供应:100 桶
发货:1天内
信息标签:多少钱@FUCHS PLANTOGEAR 100S福斯,供应,能源,润滑油(脂)

点击这里进行电话呼叫

点击这里QQ咨询

联系时一定要说在【贸易商务资源网】看到的将给您优惠！如果您也想和该公司一样在网站发信息有好排名，点击立即免费注册，发布产品推广。

润滑油0755-29672358 传真0755-29671978 ，133-9219-6659，158-2079-1590谭女士 QQ2535078038，159-9952-6096吴先生，QQ1305716027。

  

PLANTOGEAR 100 S, 150 S, 220 S, 320 S

PLANTOGEAR S products are environmentally acceptable industrial gear oils based on special saturated synthetic esters which guarantee high ageing resistance and excellent wear protection - very good lubricity. The products have a good solvency (good deterging dispersant properties due to the polar ester base oils).

PLANTOGEAR S products have high scuffing protection (FZG > 12). The selected antiwear/ extreme pressure additive system guarantees the wear protection of bearings due to the excellent FE8 roller bearing wear test results (excellent wear protection of roller bearings under severe conditions, high load, low velocity).

Application

PLANTOGEAR S products can be used as universal CLP industrial gear oils. PLANTOGEAR S products can be used in spur, bevel, planetary and worm gears, especially in environmentally sensitive areas. The products can also be used in drive systems in water protection areas where ground and surface water can be polluted by oil leaks. The formulation of PLANTOGEAR S series is based on fully synthetic saturated high-performance esters based on natural renewable resources. The products can be used in applications where the use of synthetic lubricants are of advantage.

Specifications

The products of the PLANTOGEAR S series fulfill and surpass the requirements according to:
•DIN 51 517-3: CLP
•ISO 6743-6 and ISO 12925-1: CKC / CKD / CKE
•AGMA 9005/E02: EP

The products are listed, recommended, approved by important gear manufacturers.

Advantages

Good corrosion protection
Excellent wear protection for gears and bearings
Excellent viscosity temperature behaviour, high viscosity index (VI)
Miscible with mineral oil and polyalphaolefin gear oils
Natural dissolving properties
Highest shear stability
based on renewable resources
Rapidly biodegradable (> 60% acc. to OECD 301 C)
High resistance to ageing
Good air release
Good foaming properties
Optimally suited for high and low temperature use

Instructions for use

The PLANTOGEAR S products can be used as a universal industrial gear oil in new gears as well as in used gears. New gears should be flushed and rinsed before applying PLANTOGEAR S. New gears are usually partly filled with mineral oil based corrosion protection and running in oils after manufacture. If they are not completely flushed, the running in and the corrosion protection oil remains in the gear and may contaminate the PLANTOGEAR S products. Under unfavourable conditions this can result in increased foam values and this can affect the biodegradability of the PLANTOGEAR S products negatively. The content of the residual mineral oil should, therefore, be reduced as recommended in the ISO 15380 guideline, table A1 (guidelines for changing fluid from mineral based oils to environmentally acceptable fluids) to a percentage of approximately lower than 2 % mineral oil in PLANTOGEAR S.

Old gears should also be flushed and rinsed before changing over to PLANTOGEAR S in order to reduce substantially the concentration of the residual mineral oil based product. The internal tank and gear coatings should be compatible with ester based products.

Paints which are not compatible to esters are not recommended to be used. In general two components coating systems can be used with ester based products. The use of stainless steel tanks or stainless steel filter housings is recommended.

When deep filtration filters are used, the good solvency, dissolving properties of the PLANTOGEAR S products can reduce the filter life.

Clean/check or replace the oil filters in the system after 1 week after changing over to PLANTOGEAR S products. To ensure a safe operation, when using PLANTOGEAR S products in gear and circulating systems, remove any water that may have penetrated the systems before start-up or after longer periods of down-time. We recommend the use of suitable dryer systems and filtration units. Use ester-resistant compatible sealing materials and plastic materials in general. We recommend the use of viton material in dynamic stressed seals.

Observe the change-over recommendations according to ISO 15380.

Typical technical data:

			PLANTOGEAR
Product name		100 S	150 S	220 S	320 S
Properties	Unit					Test method
Type of lubricant acc. to		CLP	CLP	CLP	CLP	DIN 51 502
DIN 51 517-3,		100	150	220	320
Labeling acc. to DIN 51 502
Labeling acc. to ISO 12 925-1		CKC	CKC	CKC	CKC	ISO 12 925-1
		100	150	220	320
Viscosity class		ISO	ISO	ISO	ISO	DIN ISO 3448
acc. to DIN ISO 3448		VG	VG	VG	VG
		100	150	220	320
Kinematic viscosity						DIN EN ISO
at 40 °C	mm²/s	100	150	220	320	3104
Viscosity index		138	145	152	155	DIN ISO 2909
Density at 15 °C	kg/m³	0.924	0.926	0.938	0.943	DIN  51 757
Flashpoint in open cup	°C	280	280	280	280	DIN EN ISO
acc. to Cleveland						2592
Pourpoint	°C	- 33	- 30	- 30	- 30	DIN ISO 3016
Neutralisation number (acidic)	mg KOH/g	0.7	0.7	0.7	0.7	DIN 51 558-1
Water content (%)	%	< 0.05	< 0.05	< 0.05	< 0.05	DIN 51 777-2
Foaming						ISO 6247
immediately and after 10 min.
Seq. I, at 24 °C	ml	0/0	0/0	0/0	0/0
Seq. II, at 93 °C	ml	20/0	20/0	10/0	0/0
Seq. III, at 24 °C	ml	0/0	0/0	0/0	0/0

			PLANTOGEAR
Product name		100 S	150 S	220 S	320 S
Properties	Unit					Test method
Demulsifying						ISO 6614
at 54 °C	min	-	-	-	-
at 82 °C (ISO VG 100 and higher)	min	15	15	20	25
Copper corrosion	degree of	1	1	1	1	DIN EN ISO
(3 h, 100 °C)	corrosion					2160
Steel corrosion,	degree of	0 - A	0 - A	0 - A	0 - A	DIN ISO 7120
method A	corrosion	(pass)	(pass)	(pass)	(pass)
Ageing						DIN EN ISO
312 h / 95 °C						4263-4
- Increase of viscosity at 100 °C	%	3.3	3	3.5	3.7
- Increase of viscosity number	ml	0	0	0	0
FZG mechanical gear test rig	failure load	> 12	> 12	> 12	> 12	DIN ISO 14
FZG A/8.3/90	stage					635-1
FE8 wear test, D7.5/80-80,						DIN 51 819-3
- roller wear	mg	< 15	< 15	< 15	< 15
- cage wear	mg	< 100	< 100	< 100	< 100
Effect on seal material SRE-NBR						DIN ISO 1817
28/SX after 7 days
± 2 h at (100 ± 1) °C
Change in volume	%	7.2	7.5	5.8	4.6
Change in hardness	%	- 6.2	- 6.7	- 5.5	- 4.0
Change in elongation	%	- 1.2	- 1.1	- 2.2	- 3.3
Change in tensile strength	%	- 14.1	- 11.7	- 12.3	- 16.5